Skip to content
Open
Show file tree
Hide file tree
Changes from all commits
Commits
File filter

Filter by extension

Filter by extension

Conversations
Failed to load comments.
Loading
Jump to
Jump to file
Failed to load files.
Loading
Diff view
Diff view
22 changes: 22 additions & 0 deletions worldsemi/addressable-led/WS2812B/SOURCES.md
Original file line number Diff line number Diff line change
Expand Up @@ -5,3 +5,25 @@
- **Source URL**: https://cdn-shop.adafruit.com/datasheets/WS2812B.pdf
- **Retrieval date**: 2026-07-01
- **Vendor**: WorldSemi (mirrored on Adafruit CDN)

## Silicon revisions V6 and V7

Both received directly from WorldSemi on 2026-11-09, in reply to a FastLED
enquiry. The vendor filenames were kept as shipped, so the revision is visible
in the name.

- **File**: `WS2812B-V6_EN.pdf`
- **Original filename**: `WS2812B-V6_EN.pdf` (not renamed)
- **Document revision**: V1.5 (footer), 9 pages
- **Source**: WorldSemi, attached to the email "Worldsemi WS2812B-V6 Datasheet and V6/V7 Current Consumption Clarification", 2026-11-09
- **Vendor**: WorldSemi (world-semi.com)

- **File**: `WS2812B-V7_EN.pdf`
- **Original filename**: `WS2812B-V7_EN.pdf` (not renamed)
- **Document revision**: V1.3 (footer), 9 pages
- **Source**: same email as above
- **Vendor**: WorldSemi (world-semi.com)

Neither revision is mirrored at a public URL, so the vendor email is the
provenance. See `current-consumption.md` for the idle-vs-transmit current
clarification that came with them.
Binary file added worldsemi/addressable-led/WS2812B/WS2812B-V6_EN.pdf
Binary file not shown.
Binary file added worldsemi/addressable-led/WS2812B/WS2812B-V7_EN.pdf
Binary file not shown.
36 changes: 36 additions & 0 deletions worldsemi/addressable-led/WS2812B/current-consumption.md
Original file line number Diff line number Diff line change
@@ -0,0 +1,36 @@
# WS2812B V6 / V7 current consumption

Vendor clarification supplied with the V6 and V7 datasheets
(`WS2812B-V6_EN.pdf`, `WS2812B-V7_EN.pdf`) on 2026-11-09. It corrects a common
modelling error: the sub-microamp figure is an **idle** number and must not be
used to estimate draw while the part is being driven.

| Condition | Current |
|---|---|
| No data signal (quiescent / idle) | **< 1 µA** |
| During data transmission (IC operating current) | **≈ 150 µA** |

Quoting the vendor: the "< 1 µA" specification *"applies to the idle state
without data transmission and should not be used directly to estimate
consumption during"* transmission.

## Why it matters for a power model

These figures are the **IC's own** supply current — they exclude the LED dice,
which dominate total draw and are set by PWM brightness, not by this number.
Treat 150 µA as the per-pixel logic overhead to add on top of the LED current
when a frame is being clocked out, and 1 µA only when the bus is idle. Using
1 µA as the active figure understates the chip's contribution by roughly 150×.

## Brightness difference between the revisions

The vendor also states that **V7 delivers three times the brightness of V6**.
That is a property of the rev, not a datasheet typo: two boards that look
identical can differ by 3× in luminous output depending on which silicon they
carry, so record the revision when comparing measurements.

## Provenance limit

The figures above are from the vendor's email of 2026-11-09 and are reproduced
here as a supplement to the PDFs; where the PDFs disagree, the PDFs win. Neither
number was measured by FastLED.
Loading